You get a bonus - 1 coin for daily activity. Now you have 1 coin

3.4. TROUBLESHOOTING FOR OTHER PERIPHERAL EQUIPMENT 3.4.1. DIAGNOSTICS AND SERVICE DEVICES INPUT - KEYBOARD AND MANIPULATOR TYPE MOUSE

Lecture



3.4.1.1. KEYBOARD DEVICE

The keyboard is designed to enter alphanumeric information and commands in the PC. The basis of the keyboard is the mat of contacts (keys). Keys can be executed

as:

  • resistive sensors that can be made using: o mechanical contacts;
    • film contacts;
    • reed contacts;
  • capacitive sensors.

The task of determining whether a key is pressed, forming its code (scan code) and transferring data to a PC is solved by a specialized micro-computer (keyboard controller). The block diagram of the controller is shown in Figure.

  3.4.  TROUBLESHOOTING FOR OTHER PERIPHERAL EQUIPMENT 3.4.1.  DIAGNOSTICS AND SERVICE DEVICES INPUT - KEYBOARD AND MANIPULATOR TYPE MOUSE
Figure 77 - Block diagram of the keyboard controller

The main elements of the controller are:

  • Clock generator
  • Binary counter
  • Decoder
  • ROM
  • selector

Output Register The keyboard communicates with the PC by a serial code.

The order of keyboard interaction with the PC is shown in Figure.

  3.4.  TROUBLESHOOTING FOR OTHER PERIPHERAL EQUIPMENT 3.4.1.  DIAGNOSTICS AND SERVICE DEVICES INPUT - KEYBOARD AND MANIPULATOR TYPE MOUSE
Figure 78 - The scheme of keyboard interaction with PC equipment

Each time the PC is turned on, the keyboard is tested by POST tests, the standard keyboard error codes for the POST procedure are displayed on the monitor screen and look like this (some BIOS types do not display keyboard error codes):

3xx - Keyboard Fault

301 - Keyboard reset failure or key sticking (XX 301, XX hexadecimal scan code)

302 - The keyboard switch on the system unit is locked

302 - User-defined keyboard test error 303 - Malfunction of the keyboard or motherboard; controller malfunction

304 - Malfunction of the keyboard or motherboard; high keyboard sync frequency

305 - Malfunction of power supply +5 V keyboard; PS / 2 keyboard fuse failed

341 - Keyboard malfunction
342 - Keyboard cable malfunction
343 - Malfunction of the cable or LED board of the keyboard

345 - Malfunction of the cable or LED board of the keyboard
346 - Keyboard Interface Cable Malfunction
347 - Malfunction of the cable or LED board of the keyboard

3.4.1.2. DEVICE MANIPULATOR TYPE MOUSE.

The mechanical mouse consists of:

    • steel rubberized ball
    • two plastic rollers with discs
    • control chip with RS-232, PS / 2, USB interface (depending on the mouse) and controller
    • scrolling movie
    • 2-3 microswitches (mostly, although it happens more).

  3.4.  TROUBLESHOOTING FOR OTHER PERIPHERAL EQUIPMENT 3.4.1.  DIAGNOSTICS AND SERVICE DEVICES INPUT - KEYBOARD AND MANIPULATOR TYPE MOUSE
Figure 79 - Basic elements of a mechanical mouse Figure 80 - Schematic diagram of a mechanical mouse

The principle of the mouse is as follows: rolling the mouse on the table, we move the ball, the ball touches the rollers with disks, through the holes of which information flows to the photodetectors. The information of their photodetectors is processed in the control chip and transmitted to the PC via a serial interface. The mouse connects to the PC 4-wire cable.

Optical mouse

The main elements of an optical mouse are (Figure 2):

      • Light source (LED or semiconductor laser)
      • Optical system
      • Sensor Light (Sensor)
      • MS signal processing (Image Processor - Image Processing Processor (DSP)).

  3.4.  TROUBLESHOOTING FOR OTHER PERIPHERAL EQUIPMENT 3.4.1.  DIAGNOSTICS AND SERVICE DEVICES INPUT - KEYBOARD AND MANIPULATOR TYPE MOUSE
Figure 81 - Optical device

The principle of operation of an optical mouse is as follows: using an LED, and a system of lenses focusing its light, a surface area is highlighted under the mouse. The light reflected from this surface, in turn, is collected by another lens and hits the receiving sensor of the microcircuit - the image processing processor. This chip, in turn, takes pictures of the surface under the mouse at a high frequency (kHz). Based on the analysis of a series of consecutive images (representing a square matrix of pixels of different brightness), the integrated DSP processor calculates the resulting figures indicating the direction of movement of the mouse along the X and Y axes and transmits the results of its work to the outside through the serial port.

3.4.1.3. PREVENTIVE MAINTENANCE OF THE KEYBOARD AND MOUSE.

Keyboard cleaning

To maintain the keyboard in working condition, it must be cleaned. For prevention, it is recommended to clean it once a week (or at least once a month) with a vacuum cleaner. Instead of a vacuum cleaner you can use a miniature compressor to blow out dust and dirt. While cleaning with a compressor, hold the keyboard with the keys down. Once a year it is recommended to perform a full cleaning with a complete disassembly of the keyboard and washing in a soap solution of all the keys and the keyboard housing.

Keyboard replacement

It is often much easier and cheaper to replace the keyboard than to repair it, especially if the electronic "stuffing" or one of the keys is faulty. It is almost impossible to get spare parts, but even if they are, the procedure for replacing them is quite difficult.

Cleaning the mouse pad

The "slippage" of a mechanical mouse most often occurs due to the fact that dust and dirt have got inside the case. You can use a brush or cotton swabs to clean the mouse’s gut and remove the belt from the rollers with a match from the dirt. It is advisable not to touch the optical system: photo and LEDs. When they are displaced, the mouse may not work.

Very often during operation, both mechanical and optical mice, due to frequent bending, there is a break in the wires in the cable. As a rule, such a failure is indicated by the fact that the mouse is either working or not. The wires in the cable usually break off near the body of the mouse or near its connector. It is possible to determine the place of the break using a tester or by moving the cable with one hand and the mouse with the other.

If the cable near the mouse case is damaged, the cable is cut off at a distance of about 5 cm from the case. Solder the rest of the old cable and solder a new one.

It is more difficult if the cable is damaged near the connector as it is not collapsible. You can take a cable with a connector, from any mouse or search for a new connector.


Comments


To leave a comment
If you have any suggestion, idea, thanks or comment, feel free to write. We really value feedback and are glad to hear your opinion.
To reply

Diagnostics, maintenance and repair of electronic and radio equipment

Terms: Diagnostics, maintenance and repair of electronic and radio equipment